View TQM7M9023_6082726.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) functional block diagram data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 1 features ? quad-band linear gsm/edge ? umts b1 and b5/8 ? input power controlled ? gmsk and 8psk ? gsm lb has 3 modes ? hp, mp, lp ? gsm hb has 2 modes ? hp, lp ? w/cdma has 3 modes ? hp, mp, lp ? hbt/phemt / cuflip ? pa technology ? integrated coupler ? built-in voltage regulator ? 50? input and output impedance ? lead-free 260c / rohs / halogen-free ? 24 pin 5x7.5mm package applications ? gsm/edge/wedge applications ? wcdma b1/8 or b1/5 applications ? wcdma b1/5/8 applications (w/ external switch) ? hsdpa/hsupa/hspa+ applications ? lte applications / evdo reva b1&b5 package style 24-pin laminate module top view product description the TQM7M9023 is a fully matched multimode multiband power amplifier module that supports quad-band gsm/edge linear, w/cdma & lte band 1, and low band wcdma/lte (externally tuned for either band 5 or band 8). the gsm pa output power is controlled by the input pow er coming from the transceiver in both gmsk and 8psk modes. the 3-gain state wcdma pa operates in lpm, mpm and hpm to maximize talk time over the entire range of operating conditions. it also includes a coupler and built-in regulator, ideal for today?s extremely small data enabled phones. the TQM7M9023 is designed on triquint?s gaas hbt technology with cuflip? assembly offering state of the art reliability, temperature stability and ruggedness. its rf performance meets the stringent linearity requirements for multi-mode operation. electrical specifications gsm850/900 dcs/pcs umts b1 umts b5 umts b8 units ty p ty p ty p ty p ty p hpm pout 35 33 28 28.25 28.25 dbm hpm pae 55 50 40 40 40 % lpm icc @ 3.5dbm pout 888 hpm icc@psat 1.5 1 0.46 0.46 0.46 a parameter ma
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 2 absolute maximum ratings parameter symbol rating units positive supply voltage v batt , v cc -0.5 to +5.5 v control voltages (enable, v mode0 , v mode1 lb_en, hb_en, v mode0 , v mode1 -0.5 to +5.5 v input rf power p in +15 dbm storage temperature tstorage -30 to +150 c operating case (ambient) temperature tcase -20 to +90 c hbm esd esd class 1c peak reflow temperature tmax 260 c ruggedness ( pout max power, all phases) ruggedness 10:1 vswr duty cycle at maximum power 50 % moisture sensitivity level msl msl3 note 1: stresses greater than the listed absolute maximum ratings may cause permanent and functional damage to the device. note 2: exposure exceeding absolute maximum rating conditions for extended periods may affect device reliability note 3: esd hbm meets conditions defined in jesd22-a114-e. note 4: part may not survive all maximums applied simultaneously operating parameters dc supply condition min typ max unit supply voltage (v batt, v cc ) gmsk operation 8psk operation wcdma operation wcdma operation with dcdc 3.0 3.2 3.2 1.0 3.5 3.5 3.4 4.5 4.2 4.2 4.0 v v v v v mode0 , v mode1 (digital control) lb_en, hb_en low high current 0 1.35 1.8 0.5 3.1 0.1 v v ma rise time from pout = -30 dbm to pout = pmax 1 s fall time from pout = -30 dbm to pout = pmax 1 s operating case temperature -20 +85 c umts turn on/off time dc: icc to within 90% of final value rf: pout within 1db of final value 20 6 s s mode switching time with pa_on = high 2 s
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 3 modes of operation mode of operation lb_en hb_en mode v mode0 v mode1 v batt v cc powerdown low low x 1 x 1 x 1 on on gsm 850/900 ? high-power mode high low low low low on on gsm 850/900 ? medium-power mode high low low low high on on gsm 850/900 ? low-power mode high low low high low on on dcs/pcs ? high-power mode low high low low low on on dcs/pcs ? low-power mode low high low high low on on umts band 5/8 ? high-power mode high low high low x on on umts band 5/8? medium power mode high low high high low on on umts band 5/8? low-power mode high low high high high on on umts band 5/8? optional lower vcc high low high high high on 1.5v umts band 1 ? high-power mode low high high low x on on umts band 1 ? medium power mode low high high high low on on umts band 1 ? low-power mode low high high high high on on umts band 1 ? optional lower vcc low high high high high on 1.5v note 1: logic input currents will be minimized when mode, vmode0 and vmode1 are low. recommended gsm power levels for each mode of operation gmsk modes pcl output power range low band ? high-power mode 5-6 30.5 dbm < p out psat low band ? medium power mode 7-13 16 dbm < p out 30.5 dbm low band ? low-power mode 14-19 p out 16 dbm high band ? high-power mode 0-7 16 dbm < p out psat high band ? low-power mode 8-15 p out 16 dbm recommended edge power levels for each mode of operation 8psk modes pcl output power range low band ? high power mode 8-9 23 dbm < p out 29dbm low band ? medium power mode 10-15 14 dbm p out 23dbm low band ? low-power mode 16-19 p out 12 dbm high band ? high-power mode 0-10 10 dbm < p out 28dbm high band ? low-power mode 11-15 p out 10 dbm recommended wcdma power levels for each mode of operation 8psk modes output power range band 5/8 ? high power mode 17 dbm < p out 28.25 dbm band 5/8 ? medium power mode 9 dbm p out 17 dbm band 5/8 ? low-power mode / optional lower vcc p out < 9 dbm band 1 ? high-power mode 17 dbm < p out 28 dbm band 1 ? medium power mode 8 dbm p out 17 dbm band 1 ? low-power mode / optional lower vcc p out 8 dbm
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 4 gsm 850/gsm 900 band electrical characteristics 1 parameter conditions min typ max units operating frequency range gsm 850 gsm 900 824 880 849 915 mhz mhz input power 9 dbm maximum output power gmsk hpm gmsk hpm (degraded power) 8psk (rms power) low power mode 34.5 32.5 14.0 35 29 dbm dbm dbm dbm power added efficiency (pae) gmsk hpm, p out = p sat _hpm gmsk mpm, p out = p sat _mpm 8psk hpm, p out = 29dbm gmsk lpm i batt , p out = 6dbm 55 41 28 70 % % % ma gain high-power mode p out = 34.5 dbm medium-power mode p out = 30.5 dbm low-power mode p out = 14 dbm 26.5 23.5 13 33.5 31.0 22.0 db db db gain variations ? tc -25< tc < 90c (all modes) 1.5 db gain variations ? v batt 3.2 < v batt < 4.2v (all modes) 1 db 400 khz, p out 28dbm 400 khz, all power levels -60 -45 -57 -40 dbc/30 khz dbm/30khz edge acpr 2 600 khz, p out 19dbm 600 khz, all power levels -70 -60 -63 -55 dbc/30 khz dbm/30khz edge evm all modes 3 % rx band noise rx=869-894 mhz -87 dbm/100 khz rx=925-935 mhz -84 dbm/100 khz rx=935-960 mhz -87 dbm/100 khz harmonics 2 fo, p out 34.5dbm 3fo-5fo, p out 34.5dbm -10 -15 dbm dbm input impedance 2:1 vswr stability load vswr 8:1 in band, all phase angles -36 dbm ruggedness p out 34.5dbm 10:1 note 1 : performance referenced to module pin under the following conditions unless otherwise specified: t=25c, vcc=3.5v, duty =25%, pulse width =1154us, lb_en = high note 2 : acpr spec referenced in dbc is relaxed by 1db for every 1db p out change for all power levels less than 28dbm for 400khz and all power levels less than 19dbm for 600khz. acpr spec re ferenced in dbm holds for all power levels and all modes.
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 5 dcs 1800/pcs 1900 band electrical characteristics 1 parameter conditions min typ max units operating frequency range dcs 1800 pcs 1900 1710 1850 1785 1910 mhz mhz input power 6 dbm maximum output power gmsk high power mode gmsk hpm (degraded power) 8psk (rms power) low power mode 32.2 30.3 14.0 33 28 20 dbm dbm dbm dbm power added efficiency (pae) gmsk hpm, p out = p sat _hpm gmsk lpm, p out = p sat _lpm 8psk hpm, p out = 28 dbm gmsk lpm i batt , p out = 1dbm 50 23 30 45 % % % ma gain high power mode p out = 32.0 dbm low power mode p out = 14 dbm 27.0 13 32.5 22 db db gain variations ? tc -25< tc < 90c 1.5 db gain variations ? v batt 3.2 < v batt < 4.2v 1 db 400 khz, p out 28dbm 400 khz, all power levels -60 -45 -57 -40 dbc/30 khz dbm/30khz edge acpr 2 600 khz, p out 14dbm 600 khz, all power levels -73 -60 -65 -55 dbc/30 khz dbm/30khz edge evm all modes 3 % rx band noise rx=1805-1880 mhz -83 dbm/100 khz rx=1930-1990 mhz -83 dbm/100 khz harmonics 2 fo, p out 32.3dbm 3fo-5fo, p out 32.3dbm -10 -15 dbm dbm input impedance hpm, mpm lpm 2.0:1 2.5:1 vswr vswr stability load vswr 8:1 in band, all phase angles -36 dbm ruggedness p out 32.3dbm 10:1 note 1 : performance referenced to module pin under the following conditions unless otherwise specified: t=25c, vcc=3.5v, duty =25%, pulse width =1154us, hb_en = high note 2 : acpr spec referenced in dbc is relaxed by 1db for every 1db p out change for all power levels less than 28dbm for 400khz and all power levels less than 14dbm for 600khz. acpr spec re ferenced in dbm holds for all power levels and all modes.
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 6 test signal configuration parameter symbol definition hpsk modulated carrier in 3.84 mhz bw ul ref. meas. channel (12.2kbps) from 3gpp ts25.101 annex a sec. a.2.1 1 dpcch@15ksps, spread code=0, relative power=-6.547 db 1 dpdch@60ksps, spread code=16, relative power=-1.087 db voice, rel99 tc1 cw testing, input power adjusted to meet output power requirements dpcch@15ksps, spread code=0, relative power=-19.391 db, q branch dpdch@960ksps, spread code=1, relative power=-13.931 db, i branch hs-dpcch@15ksps, spread code=64, relative power=-19.391 db, q branch e-dpcch@15ksps, spread code=1, relative power=-17.338 db, i branch e-dpdch1@960ksps, spread code=2, relative power=-0.371db, i branch hsupa, mpr=0db tc2 cw testing, input power adjusted to meet output power requirements evdo rev a rev a evdo rev a signal using subtype 2 physical layer with a payload size of 4096 bits
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 7 rf electrical characteristics ? band 1 1, 2 parameter power mode conditions min typ max unit frequency all modes umts band 1 1920 1950 1980 mhz maximum output power 3 hpm hpm hpm hpm wcdma rel99 waveform 2 (tc1) worst case 3gpp; mpr = 0 db (tc2) cdma evdo reva modulation lte, mpr=0db 28 27 27 27 dbm dbm dbm dbm gain hpm mpm lpm p out max power p out 17dbm (16dbm 3gpp mpr = 0) p out 8dbm ( 6dbm 3gpp mpr = 0) 24 13 8 29 22 16 db db db noise power in rx band all modes 190 mhz offset from tx at all powers -140 dbm/hz quiescent current (icq) mpm lpm no rf applied 15 5 ma ma supply current hpm lpm p out = 28 dbm p out = 3.5dbm 460 8 ma ma error vector magnitude (evm) p out (maximum power ? mpr) 2.5 % rms 5 mhz, pout (maximum power - mpr) -36 dbc umts adjacent channel leakage power ratio (aclr) all modes 10 mhz, pout (maximum power - mpr) -46 dbc e-utra aclr ; p out (26.75dbm ? mpr) -33 dbc utra aclr1 ; p out (26.75dbm ? mpr) -36 dbc lte adjacent channel leakage power ratio (aclr) all modes utra aclr2 ; p out (26.75dbm ? mpr) -39 dbc adjacent channel power ratio (acpr) all modes hpm 27dbm; mpm 17dbm; lpm 8dbm 1.98mhz; 885khz -44 -56 dbc / 30khz dbc / 30khz harmonic suppression h2 p out maximum power -35 dbc harmonic suppression h3 and higher p out maximum power -42 dbc gps noise all modes 1574 ? 1577 mhz -140 dbm/hz gps band gain where g is gain in tx band g-3 db ism noise all modes 2400 ? 2483.5 mhz -143 dbm/hz ism band gain where g is gain in tx band g-6 db band 34 noise all modes 2010 ? 2025 mhz, 100rb qpsk lte signal centered at 1970mhz at lte max power -35 dbm/mhz lte ns_05 phs noise 4 1884.5 ? 1919.6 mhz -42 dbm/300khz input impedance vswr all modes no external matching 2.0:1 stability (all spurious) all modes load vswr 6:1 in band, all phases -70 dbc coupling factor all modes 20 db note 1: rf measurements under the following conditions unless otherwise specified: vcc=3.4v, t=25, note 1: rel99 waveform. note 2: rf measurements shall be made with 3gpp (utran/fdd ue) ts25.101 specification compliant waveforms. (a) rel99 waveform (all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. mpr is the maximum powe r reduction, worse case mpr = 0db waveforms across umts technologies are required to meet a 1 db lower maximum power than rel99. signal configuration: 3gpp (dpcch + 1dpd ch) up-link unless specified otherwise. note 3: for v cc < 3.4v operation, up to a 0.5db back-off is allowed for maximu m power output. for vcc=3.4v, t=85c, up to a 0.5db back-off is allowed for maximum power output. note 4: p out 28dbm for qpsk, 5mhz bw, 8rb; p out 23dbm for qpsk, 10mhz bw, 50rb; p out 22dbm for qpsk, 20mhz bw, 100rb
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 8 rf electrical characteristics ? band 5 1, 2 parameter power mode conditions min typ max unit frequency all modes umts band 5 824 849 mhz maximum output power 3 hpm hpm hpm hpm wcdma rel99 waveform (tc1) worst case 3gpp; mpr = 0 db (tc2) lte, mpr=0db cdma evdo reva modulation 28.25 27.25 27.25 27 dbm dbm dbm dbm gain hpm mpm lpm p out max power p out 17dbm (16dbm 3gpp mpr = 0) p out 9dbm ( 6dbm 3gpp mpr = 0) 27.6 18 11.7 db db db noise power in rx band all modes 190 mhz offset from tx at all powers -133 dbm/hz quiescent current (icq) mpm lpm no rf applied 15 5 ma ma supply current hpm lpm p out = 28.25 dbm p out = 3.5dbm 460 8 ma ma p out (maximum power ? mpr) 3.35 % rms error vector magnitude (evm) p out (maximum power ? mpr ? 3 db) 2.5 % rms 5 mhz, p out (maximum power - mpr) -36 dbc umts adjacent channel leakage power ratio (aclr) all modes4 10 mhz, p out (maximum power - mpr) -46 dbc e-utra aclr ; p out (27dbm ? mpr) -33 dbc utra aclr1 ; p out (27dbm ? mpr) -36 dbc lte adjacent channel leakage power ratio (aclr) all modes utra aclr2 ; p out (27dbm ? mpr) -39 dbc adjacent channel power ratio (acpr) hpm 27dbm mpm 17dbm lpm 8 dbm 885khz; pout 27dbm 1.98mhz; pout 27dbm -44 -56 dbc/30khz dbc/30khz harmonic suppression h2 pout maximum power -35 dbc harmonic suppression h3 and higher pout maximum power -42 dbc gps noise all modes 1574 ? 1577 mhz -140 dbm/hz gps band gain where g is gain in tx band g-25 db ism noise all modes 2400 ? 2483.5 mhz -143 dbm/hz ism band gain where g is gain in tx band g-30 db input impedance vswr all modes no external matching 2:1 stability (all spurious) all modes load vswr 5:1 in band, all phases -70 dbc coupling factor all modes 20 db note 1: rf measurements under the following conditions unless otherwise specified: vcc=3.4v, t=25, zin/zout=50ohm, rel99 waveform. all measurements are based upon tuning optimized for ba nd 5 performance. please see application note for more information. note 2: rf measurements shall be made with 3gpp (utran/fdd ue) ts25.101 specification compliant waveforms. (a) rel99 waveform (all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. mpr is the maximum powe r reduction, worse case mpr = 0db waveforms across umts technologies are required to meet a 1 db lower maximum power than rel99. signal configuration: 3gpp (dpcch + 1dpdch) up-link unless specified otherwise. note 3: for vcc < 3.4v operation, up to a 0.5db back-off is allowed for maximum power output. for vcc=3.4v, t=85c, up to a 0.5db back -off is allowed for maximum power output.
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 9 rf electrical characteristics ? band 8 1, 2 parameter power mode conditions min typ max unit frequency all modes umts band 8 880 915 mhz maximum output power 3 hpm hpm hpm wcdma rel99 waveform (tc1) worst case 3gpp; mpr = 0 db (tc2) lte, mpr = 0db 28.25 27.25 27.25 dbm dbm dbm gain hpm mpm lpm p out max power p out 17dbm (16dbm 3gpp mpr = 0) p out 9dbm ( 6dbm 3gpp mpr = 0) 24.5 13 8 29.5 22 16 db db db noise power in rx band all modes 190 mhz offset from tx at all powers -137 dbm/hz quiescent current (icq) mpm lpm no rf applied 15 5 ma ma supply current hpm lpm p out = 28.25 dbm p out = 3.5dbm 465 8 ma ma p out (maximum power ? mpr) 3.35 % rms error vector magnitude (evm) p out (maximum power ? mpr ? 3 db) 2.5 % rms 5 mhz, p out (maximum power - mpr) -36 dbc umts adjacent channel leakage power ratio (aclr) all modes4 10 mhz, p out (maximum power - mpr) -46 dbc e-utra aclr ; p out (27dbm ? mpr) -33 dbc utra aclr1 ; p out (27dbm ? mpr) -36 dbc lte adjacent channel leakage power ratio (aclr) all modes utra aclr2 ; p out (27dbm ? mpr) -39 dbc harmonic suppression h2 pout maximum power -35 dbc harmonic suppression h3 and higher pout maximum power -42 dbc gps noise all modes 1574 ? 1577 mhz -140 dbm/hz gps band gain where g is gain in tx band g-25 db ism noise all modes 2400 ? 2483.5 mhz -143 dbm/hz ism band gain where g is gain in tx band g-30 db input impedance vswr all modes no external matching 2.0:1 stability (all spurious) all modes load vswr 5:1 in band, all phases -70 dbc coupling factor all modes 20 db note 1: rf measurements under the following conditions unless otherwise specified: vcc=3.4v, t=25, zin/zout=50ohm, rel99 waveform. all measurements are based upon tuning optimized for ba nd 8 performance. please see application note for more informa tion. note 2: rf measurements shall be made with 3gpp (utran/fdd ue) ts25.101 specification compliant waveforms. (a) rel99 waveform (all beta_c, beta_d combinations) has very low peak-to-average power ratio and has its own requirement. mpr is the maximum powe r reduction, worse case mpr = 0db waveforms across umts technologies are required to meet a 1 db lower maximum power than rel99. signal configuration: 3gpp (dpcch + 1dpdch) up-link unless specified otherwise. note 3: for vcc < 3.4v operation, up to a 0.5db back-off is allo wed for maximum power output. for vcc=3.4v, t=85c, up to a 0.5 db back-off is allowed for maximum power output.
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) pin out and assignments rf in umts hb rf in gsm hb hb_en v mode0 v mode1 mode gnd v batt lb_en rf in gsm lb rf in umts lb gnd rf out umts hb gnd rf out umts lb gnd rf out gsm hb gnd rf out gsm lb gnd v cc umts v cc gsm cpl out cpl in pin symbol description 1 rf in umts hb rf input for high band wcdma amplifier (band 1) 2 rf in gsm hb rf input for dcs/pcs amplifier 3 hb_en enables hb (dcs/pcs) amplifier 4 v mode0 logic input to set amplifier mode 5 v mode1 logic input to set amplifier mode 6 mode logic input to set amplifier mode ? wcdma or gsm 8 v batt battery voltage 9 lb_en enables lb (gsm) amplifier 7,14,16,19,21,23 gnd gnd pin 10 rf in gsm lb rf input for gsm850/900 amplifier 11 rf in umts lb rf input for low band wcdma amplifier (band 5/8) 12 cpl in coupler input 13 rf out gsm lb rf output for gsm850/900 amplifier 15 rf out gsm hb rf output for dcs/pcs amplifier 17 v cc gsm voltage supply to vcc gsm 18 v cc umts voltage supply to vcc wcdma 20 rf out umts lb rf output for low band wcdma amplifier (band 5/8) 22 rf out umts hb rf output for hi gh band wcdma amplifier (band 1) 24 cpl out coupler output data shee for a dditional information and the latest specifications, see our website: www.triquint.com t revision f,september, 2011 10
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) package dimensional drawings: data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 11
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) package land pattern: data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 12
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) package marking triquint: product name: year, work week, country code: vendor code and assembly # TQM7M9023 yy= year, ww= work week, cccc= country code aa= vendor, xxxx= triquint assembly number tape and reel specification: data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 13 613017 carrie r tape - 3m part # 3m053091, cavity: length=5.40mm, width=7.90m m, depth=1.40mm, pitch = 8mm carrier tape: width = 16mm cover tape - 3m part # 2678 13.3mm wide note: packaged quantity is 2,500 per reel
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) shipment box & label description: tape & reels will be packaged in a dry-pack bag and then in a ship ment box. the box dimensions will depend on the number of ree ls shipped in each box and are noted in the table below. the box label and a description of each item on the label are also shown below. data sheet for additional information and the latest specifications, see our website: www.triquint.com revision f,september, 2011 14 13 inch x16mm--drypack box size reel qty/box empty box wt w/ packing 15x15x7 3 2 18x15x11 5 2.36 17x16x17 9 2.76 ship from: triquint semiconductor, inc 2300 ne brookwood parkway hillsboro, or 97124 ship to: recipient address information here (3s) pkg id: 581+23047123 (k) trans id: 812934657 (p) cpn: 5871-2489 (q) qty: 20000 (1p) spn: tqd777001 (13q) pkg count: 1/1 package weight 3.0 lb / 1.36 kg mpn: 1005859 supplier code: 10 character max. + tqs shipper number. (pkg. id/serial number) customer purchase order. 20 character max. customer part number. 22 character max. supplier product number. 21 character max. quantity. box count (1/3, 2/3, etc.) manufacturer's part number format: 4 * 6.5 in 102 * 166 mm code 39 1:2 all barcodes contain data identifier followed by data, e.g. k812934657
TQM7M9023 data sheet 5.0x7.5mm m ultimode m ultiband p ower a mplifier (mmpa) (quad-band gsm / edge and tri-band w/cdma/hspa+/lte) data shee for a dditional information and the latest specifications, see our website: www.triquint.com t revision f,september, 2011 15 additional information 1 this part is compliant with rohs directive (restrictions on the use of certain hazardous substances in electrical and electroni c equipment) and compliant to ipc/jedec j-std-033b.1. the part is rated moisture sensitivity level 3 at 260 degrees c per jedec standard ipc/jedec j-std-020. 1 for latest specifications, additional produc t information, worldwide sales and dist ribution locations, and information about triquint: web: www.triquint.com tel: (503) 615-9000 email: info_wireless@tqs.com fax: (503) 615-8902 the information provided herein is believed to be reliable; triquint assumes no liability for inaccuracies or omissions. triqui nt assumes no responsibility for the use of this information, and all such information shall be entirely at the us er's own risk. prices and specifications are subject to change without notice. no patent rights or licenses to any of the circuits described herein are implied or granted to any third party. triquint does not authorize or warrant any triquint product for use in life-support devices and/or systems. copyright ? 2004 triquint semiconductor, inc. all rights reserved .

▲Up To Search▲

Price & Availability of TQM7M9023

	To Download TQM7M9023 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .